Is your parallel fence not keeping up and is crooked? Our utility model registered by the patent attorney now puts an end to this! The 11-fold bearing roller slide conversion kit for your Bosch GTS 10 xc rip fence is the unbeatable remedy for crooked cuts caused by the rip fence. Thanks to readjustable roll angles, it is possible to allow the rip fence to run in the aluminum guide rail without play. So that the rip fence is permanently parallel to the saw blade and can be moved, the side of the clamping mechanism is equipped with an additional ball bearing. A 1,5mm hex key is required to adjust the play. This is not included in the scope of delivery.
Please see the video for assembly.
Included:
-2x roll angle (ball bearings)
-1x idler (ball bearings) including fastening screw
The roller carriages fit the Bosch GTS 10xc table saw with the following article numbers:
– 3 601 M30 400
– 3 601 M30 401
– 3 601 M30 402
– 3 601 M30 403
– 3 601 L30 400
-3 601 M30 431
-0 601 B30 400
New expansion
NEW: Due to the great feedback from the community, we have added a small extension. It turned out that when using our conversion kit for the Bosch GTS 10xc rip fence in combination with a heavy milling fence, such as the one from BP tools in the Aluline version, a slight tipping over the rear idler could occur. Our new extension widens the back of the Bosch GTS 10xc rip fence and thus increases the contact surface. Of course, thanks to its flat design, this extension is compatible with other milling stops for the GTS 10xc. The extension is also adjustable to eliminate wobbling caused by manufacturing tolerances. If you already have the conversion kit for the rip fence but would like to order the new extension separately, take a look please stop here. There you can order the extension individually.
The Fused-3D GbR has no economic connection to Bosch GmbH. The name Bosch is only used here as part of the product offered to describe it. This offer has no connection to Bosch GmbH and is not an original spare part for the Bosch GTS 10xc. We only sell self-designed and manufactured modifications for power tools and other tools. Use of these modifications is at your own risk! Fused-3D GbR assumes no liability for damage caused by our products!
On Fused-3D exclusive
We are proud to announce that Fused-3D has received a utility model for our roller slide conversion kit for the rip fence, making our product an exclusive solution that is only available from us. With the Roller Slide Conversion Kit for the rip fence, you get a unique product that will help you tackle your projects with ease and precision.
Stephan (Verified owner) -
Great solution, easy installation. No more crooked or tricky rip fences
Florianf -
I'm more than thrilled with the exchange, which went very quickly. Do I now have to align my circular saw so that it is level, otherwise the fence will roll away? Super easy to adjust and no more tilting. Thank you very much for that and continued success.
Viko -
This extension significantly upgrades the saw. Installation was very easy thanks to the video instructions. I am super satisfied. Thank you. Keep it up.
René Reiche -
Through the renovation of the
The circular fence has a clear parallel stop with the gliders for me
Added value. I use the saw at the same time as a table milling machine
The rip fence can now be moved much more easily, even if the
Suction device is mounted on the stop. In combination with the
I can now finally fine-tune it to the tenth of a millimeter without having to take forever to adjust.
Rene G. -
After the conversion, the stop runs as if by itself; adjusting it to a specific dimension is now very easy and, above all, repeatable. The stop can be moved with millimeter precision without any effort, simply great! In the original state, setting the measurements was a bit fiddly, the stop was fiddly and the measurement always had to be adjusted by tapping lightly against the stop.
I can only recommend the conversion to everyone.
Zdenek -
Hello. The package arrived alright. Additionally I
wanted to buy the fine tuner, but I was completely put off by the shipping. There
was no notification sent that they were coming to deliver. No email, no SMS, no
call, just nothing. If my daughter wasn't at home, I'd have no idea where
package would have gone otherwise. After installation, enthusiasm came
immediately, it slides really smoothly. But excitement only lasts until the
longitudinal stop is fixed. After tightening the lever, the longitudinal guide
on the side where the magnifier is, gets raised a little and so does not hold
very firm. I would appreciate it if someone could advise me how to eliminate
this error. If nothing can be done about it, I will be forced to refit the
original, which would be a shame. Zdenek.
A. Küpper -
I'm more than satisfied. Fast delivery, easy assembly and real added value for the circular saw.
Robert Doll -
This thing is so cool. Can't believe how well this works now. Thank you. I have even more fun working with the GTS.
Daniel -
If I were Bosch, I would install the parts at the factory! No comparison to before.
mathojojo -
Very easy to assemble and adjust thanks to the help of the little YouTube video. It remains to be seen how it holds up over time, but no doubt, the rip fence has become very repeatable and pleasant to move!!!
However, a small note: After changing the rip fence, the parallelism setting to the blade is no longer correct at all (approx. 5 mm difference along the length of the fence). The difference is so big that it was very difficult for me to restore the correct parallelism (if I had had to make up 1 mm more, it would probably have been impossible).____________________________________________________________________________________________Very easy to set up and adjust, thanks to the help of the little Youtube video. It remains to be seen how it lasts over time, but there is no doubt that the rip fence has become very repeatable and pleasant to move!
However, a small remark: Following the modification of the rip fence, the adjustment of the parallelism in relation to the blade is no longer correct (about 5mm difference on the length of the fence). The difference is so important that I had a lot of trouble to get the parallelism back to the blade (if I had to make up 1 mm more, I think it would have been impossible).
Ingo Beck -
The best conversion or improvement I have made for my Bosch GTS 10 XC. My great respect to the young team ????????????. I hope you stay active and give us more such good projects. I say thank you and wish you a merry Christmas and a happy new year. Greetings Ingo
beer professional -
Best upgrade, this is really hella good.
Jürger Lieser -
Absolutely awesome! A difference like day and night. The bearings are worth every penny! Thank you!
Tobias -
Great part! Brilliantly implemented. GTS-10 owners who don't buy this gadget definitely have themselves to blame! Of all the attachments for the TKS, it's the best I've ever seen!
Assembly in 5 minutes, parallel stop finally 100% parallel again and extremely smooth - in summary: CLEAR BUY RECOMMENDATION!
The only point of criticism: the rear ball bearing could be replaced by one with a rubber cover, steel on aluminum certainly only works to a limited extent in the long run.
Thomas -
Previously, I had corresponding spare parts from 3D printing without ball bearings from another provider. These initially had little play. Over time, however, the play increased again - probably due to abrasion. This certainly won't happen with the ball bearings. Installation is easy and you can actually adjust the bearings to be both play-free and smooth, as shown in the video. If they still prove to be durable, the price of €40 is very reasonable.
Michael -
Hello Fused 3D TeamVery good, I'm very happy with the ball-bearing roller slides for the Bosch GTS10 XC. Also the hexagon socket screw, which is now easier to access from the outside. to adjust the game, on the aluminum profile. Wonderful.I also liked the packaging, packed with love, very neat. TIPTOP. The package of gummy bears is for my wife. It's rare to see that the truth from a small business is packaged so flawlessly. Keep it up. Thanks
tiobb -
100% recommendation from me too
Adrian -
The stop works great, but what I haven't figured out yet is how to achieve 100% parallelism of the stop, because I still have to check with a stop ruler.
However, the play is significantly less than without the conversion kit and, above all, it is always the same inaccuracy of around +1,5mm at the top end and not a random deviation of +/- 3-5mm. ????
I think that you have to remove and reinstall the gliders a few times and play with the adjusting screws until they are aligned exactly the same, then the play should actually disappear.
Perhaps more detailed instructions could be provided?
Otherwise the conversion is very easy; more like five minutes than 15 minutes.
However, I was a bit confused as there has apparently been a revision since the video was produced; The grub screw (with 1,5 Allen) for adjusting the play was replaced by a larger (M3?) cylinder head screw. However, this is now easier to reach and can be easily adjusted.
However, you have to be aware of one thing: the super smooth movement of the stop across the table, as you know from numerous YouTube videos, does not entirely correspond to reality. You can certainly adjust the bearings so that with a slight tap, the parallel stop runs over the entire rail with the ball bearings purring, or it feels like it is floating.
However, this meant a very big game of attack; the bearings need a certain amount of pressure to keep the stop somewhat parallel. Apart from that, it's very annoying when the stop moves so extremely smoothly, as even with the lightest tap you move it by 3-4mm.
If you tighten the bearings a little tighter, the stop still slides very well (and worlds better than before the conversion), so you can still set it at any point and move it without any effort - and above all without tilting (!). shift, but much more precisely. Less show effect, but significantly more benefit.
Delivery should take 7-14 days, after 10 days the package arrived. Can't say anything. ?????????
Gerard Heidema -
I just installed the modification on my new Bosch GTS XC10.
The installation is very easy and the result is great. Top quality!
Gerard H., Netherlands
Manuel Steger -
HelloDoes it only fit the item numbers mentioned? I have the 0601B30400... I ordered a set and only saw afterwards that the matching item numbers for the Gts 10 Xc were there.
Nils -
Simply an ingenious extension for the GTS 10 that takes it to a higher level! You have my recommendation.
Arno Schwochow -
Finally. I widened my table with another original rail on each side. I only succeeded in making the connection 99% of the time, which is why the attack was really awkward. Now it actually works like in the video, unbelievable. A mega upgrade and great relief at work. Congratulations for this innovation.
Greg -
Whew…. Finally!!
High-end produst. Worth all the money. It’s not the same saw anymore.Fortunately, there are still some people who think and can do something like that.Thank you for Goldbären.
Regards
Bruno Müller -
TOPReceived yesterday, installed today and I'm absolutely thrilled. Top quality.
Kurt -
Got it today..installed right away...so there's really no comparison to the original...the stop almost floats over the table and there's no need to connect the stop, just great ?????????can only recommend the set to anyone who wants their stop from who wants to make the GTS 10 XC float????????????????
Matthias Leopoldseder -
Really innovative product that makes working with the GTS a world of improvement. Installation and adjustment are absolutely no problem thanks to instructions on YouTube.
PA -
Sensational, simply outstanding! The conversion kit works great and puts the Bosch GTS 10 rip fence on rails. The easy conversion can be completed in 10 minutes. Just watch the explanatory video. I use the Sauter milling fence, which means my rip fence easily weighs twice as much. Nevertheless, it now glides over the table and no longer warps or gets stuck. Worth every penny! Keep it up.
Peter Franken -
I received this conversion kit today and will install it later. I'm very excited in advance because I saw the video and believe in the abilities of these young people. In my opinion, these start-up companies are our great future and such idea platforms should be promoted and supported much more by the state. Keep it up, your idea for this product is first class and has not come close to being achieved by the actual manufacturer. Conclusion: the Bosch table saw is significantly enhanced by your well-thought-out idea and the development of your product.
Hertler, Siegmund -
Very good!
Thomas Light -
I am absolutely thrilled with the conversion kit. Thanks to the ball bearings, the stop now runs great. In particular, the rip fence now also deserves its name. Before, it was actually always stuck crooked. Keep it up and come up with some more brilliant hacks. I'm looking forward to it...Greetings Thomas Licht
Florianf -
Installed, tried, works perfectly. There's nothing more to say
Erwin Boehm -
Great and very good solution. I'm thrilled you can move the stop with just one finger. And it couldn't be easier to set up and install in 10 minutes. Dear Severin von fused-3d, you definitely got my recommendation from me, keep it up. Greetings Erwin Boehm
thobac -
Class. Installed immediately upon receipt, runs super easily. The next day I didn't think about it and adjusted the stop with the “usual” force - oooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooooonn'n't think about it the next day, I adjusted the stop with the "usual" force - wow
Heinz -
Simply great. The installation was quick and then all you have to do is enjoy. Thank you for this great part.
Harald -
Super well thought out solution. I installed it straight away and it works perfectly. I can only recommend. Keep it up.
Christian Glauert -
Great concept, fits perfectly and is installed in just a few minutes! Finally no more tilting of the rip fence, it can be moved playfully with just one finger. Using a grub screw, the seat of the slide in the guide rail of the GTS can be adjusted with almost no play, meaning that the slide is parallel after clamping immediately without any repairs.
In addition, you fused-3d The team is super friendly and responds quickly to questions, so I'm happy to respond to your request for honest and independent feedback here.
https://youtu.be/rc8kS8n4QQ8
I'm excited!
Dear Severin von fused-3d, you definitely have my recommendation…keep it up!
Francis Schmidt -
This product is very good and fits the machine exactly. I tried it out straight away, am happy with it and will order another one in reserve
Ralph Kneidl -
Top product, very professionally thought out and technically flawless and implemented in high quality. Installed in just a few minutes, the running clearance can be adjusted very precisely. The stop now runs extremely easily and, above all, parallel. This prevents crooked fixation (clamping). Actually a must-have for the GTS10XC. Clear recommendation!!
Jürgen -
Hello, is this also available for my Bosch GTS 635-216?
t.giesler@gmx.de (Verified owner) -
Finally a solution that makes the rip fence usable sensibly and precisely within the scope of the possibilities of a GTS 10XC. The conversion was relatively easy, I only had to file the rear glider so that it fit completely.
Thomas Lawrence (Verified owner) -
Very clean and high quality parts.
Easy construction.
The attack runs as if on air cushions.